Добрый день, коллеги.
Есть новый микротик 1100dx4, добавил порты с 2-5 в бридж.
Если смотреть трафик на любом из интерфейсов в бридже, то видно что любые пакеты идут в retransmit.
При этом нет проблем с передаваемой информацией, инет есть, локальные ресурсы доступны, скорость заявленная.
Пробовал прошивки 6.43.4 и 6.42.9 (сейчас стоит, это ветка bugfix only).
Конфигурация бриджа:/interface bridge> export ve
/interface bridge
add ageing-time=5m arp=enabled arp-timeout=auto auto-mac=yes disabled=no fast-forward=no forward-delay=15s igmp-snooping=no max-message-age=20s mtu=auto name=bridge-lan priority=0x8000 \
protocol-mode=rstp transmit-hold-count=6 vlan-filtering=no
/interface bridge port
add auto-isolate=no bridge=bridge-lan broadcast-flood=yes disabled=no edge=auto frame-types=admit-all horizon=none hw=yes ingress-filtering=no interface=ether2 internal-path-cost=10 learn=\
auto path-cost=10 point-to-point=auto priority=0x80 pvid=1 restricted-role=no restricted-tcn=no unknown-multicast-flood=yes unknown-unicast-flood=yes
add auto-isolate=no bridge=bridge-lan broadcast-flood=yes disabled=no edge=auto frame-types=admit-all horizon=none hw=yes ingress-filtering=no interface=ether3 internal-path-cost=10 learn=\
auto path-cost=10 point-to-point=auto priority=0x80 pvid=1 restricted-role=no restricted-tcn=no unknown-multicast-flood=yes unknown-unicast-flood=yes
add auto-isolate=no bridge=bridge-lan broadcast-flood=yes disabled=no edge=auto frame-types=admit-all horizon=none hw=yes ingress-filtering=no interface=ether4 internal-path-cost=10 learn=\
auto path-cost=10 point-to-point=auto priority=0x80 pvid=1 restricted-role=no restricted-tcn=no unknown-multicast-flood=yes unknown-unicast-flood=yes
add auto-isolate=no bridge=bridge-lan broadcast-flood=yes disabled=no edge=auto frame-types=admit-all horizon=none hw=yes ingress-filtering=no interface=ether5 internal-path-cost=10 learn=\
auto path-cost=10 point-to-point=auto priority=0x80 pvid=1 restricted-role=no restricted-tcn=no unknown-multicast-flood=yes unknown-unicast-flood=yes
/interface bridge settings
set allow-fast-path=yes use-ip-firewall=yes use-ip-firewall-for-pppoe=no use-ip-firewall-for-vlan=no
Конфигурация интерфейса (она одинакова для всех четырёх):set [ find default-name=ether2 ] advertise=10M-half,10M-full,100M-half,100M-full,1000M-half,1000M-full arp=enabled arp-timeout=auto auto-negotiation=yes bandwidth=unlimited/unlimited \
disabled=no full-duplex=yes l2mtu=1592 loop-protect=default loop-protect-disable-time=5m loop-protect-send-interval=5s mac-address=64:D1:54:FF:37:8C mtu=1500 name=ether2 \
orig-mac-address=64:D1:54:FF:37:8C rx-flow-control=off speed=100Mbps tx-flow-control=off
Средний
Простой
